Indoor Air Quality Sensors are the measurement layer of a ventilation system, not a treatment device: they report conditions, not remove pollutants. A purifier is sized against airflow, face velocity and static pressure; a sensing point against the parameter measured, the zone represented and the accuracy a control decision requires. In Vietnam, Indonesia and Malaysia, haze, traffic PM2.5 and humidity above 80% make placement and compensation as important as the instrument.
What Indoor Air Quality Sensors Measure — and What They Do Not
Readings serve three jobs: controlling ventilation, verifying engineered measures and documenting conditions for audits. They do not replace code-required outdoor air, filtration, zone pressure differentials or air disinfection; a dashboard is not proof that a purification stage performs as claimed.
Sensing principles by parameter
CO2: NDIR instruments measure infrared absorption directly and are the accepted basis for CO2-based DCV under ASHRAE 62.1. Estimated eCO2 values suit trend display, not control loops; automatic baseline correction assumes regular near-outdoor CO2, so specify manual calibration for continuously occupied wards. PM2.5/PM10: laser scattering responds fast, but hygroscopic particles grow in humid air and inflate the optical signal — require humidity compensation. TVOC: metal-oxide elements give a trend, drift and need re-zeroing. Temperature and RH compensate other channels and flag condensation.
Accuracy claims need evidence
Request stated accuracy, drift and traceable calibration certificates, with the interval in the maintenance plan. Measurement accuracy is not removal efficiency: no sensor reading substantiates a sterilisation or air disinfection claim, which requires accredited test data at a declared airflow.
How an IAQ Monitoring System Turns Readings into Control
An IAQ monitoring system is the chain from sensor to action: transmitters, a gateway, a BMS interface, trend logging, alarms and a dashboard. Specify the protocol and object list early — BACnet/IP, Modbus RTU or MQTT — with sampling intervals and retention. A display the BMS cannot read adds little.
For demand-controlled ventilation, the BMS modulates the outdoor air damper against a CO2 setpoint while holding the code-required minimum outdoor air. Response lag of several minutes calls for proportional control with a deadband; on-off logic causes hunting. During haze, a PM2.5 channel may justify lowering the outdoor air fraction, provided minimum ventilation is preserved. At commissioning, separate faults from events: one jumping point suggests condensation or drift; a rise across zones on one AHU points to the plant.
Application Scenarios in Southeast Asian Projects
Hospital ventilation and clinics
Clinical spaces need differential pressure monitoring and, where applicable, particle counts under healthcare ventilation guidance — separate instruments with their own alarm paths. Sensing points complement them by trending CO2, particulates and RH in wards. Records should link each excursion to a work order.
Commercial HVAC, offices and clean public spaces
In commercial HVAC, sensing density should follow zone boundaries, not floor area: meeting rooms and open offices load differently. Lobbies and clean public spaces often need a display. For GBI, MyCREST, LEED or WELL submissions, confirm parameters, averaging periods and retention before hardware selection.
Retrofit example: a Kuala Lumpur office tower
A 14-storey Kuala Lumpur tower approaching green-building recertification had a BMS but no air quality inputs. The contractor fitted outdoor references at both intakes, return-duct transmitters per AHU zone and room units in meeting rooms, then logged a baseline. Two units near diffusers read low and were relocated; particle channels showed a seasonal bias until humidity compensation was enabled. Only then was DCV tuned, with minimum outdoor air held constant.
Selection and Installation Notes for Contractors and MEP Engineers
When specifying Indoor Air Quality Sensors for a retrofit, start with a zone schedule: parameter, the decision it drives, required accuracy, and the controller receiving the point.
Placement that produces representative data
Wall units sit in the breathing zone, roughly 1.1–1.8 m above floor, clear of diffusers, doors and heat sources. A return-duct probe gives a zone-averaged value for central DCV; a supply-duct probe downstream of filtration verifies what the plant delivers. Duct probes need a straight, well-mixed run and protection from condensate near cooling coils. Confirm calibration access.
Common specification errors
Recurring errors: estimated CO2 for control, one point for a mixed-occupancy floor, no humidity compensation in a tropical project, undefined BMS points, and no budget for annual verification or replacement cells.
Matching the Monitoring Layer to Air Purification Equipment
Indoor Air Quality Sensors are most useful when positioned alongside the purification sections they verify. Sample points upstream and downstream of a filter bank, ESP section or micro electrostatic (MESP) module show particle trends as a cell loads — a maintenance signal, not a performance certificate. A Super ESP metal-plate collector is a higher-capacity construction, not an upgraded MESP, so commission its baseline separately. Where plasma stages are fitted, add an ozone channel and require third-party ozone evidence (UL 2998 or equivalent).
For air disinfection, monitor operating conditions — airflow, RH, run hours — and rely on accredited test data for any efficacy statement. Purification and instrumentation have different constraints: an AHU needs plenum depth, a duct module a straight run, an FCU return module shallow clearance, while a sensing point needs representative airflow and cable routing. Coordinate both on one drawing.
If you are reviewing IAQ instrumentation alongside purification for a hospital, clinic, office or mixed-use project, we are glad to discuss a customised air purification and monitoring configuration. Airflow schedules, zone drawings and IAQ targets are enough to start a conversation.